A large plot can still be a poor fit for the villa you want. Before making an offer, match the exact parcel to its site plan, obtain the current development controls and ask a design consultant to test your brief against them. The plot area tells you how much land you have. It does not tell you the permitted footprint, gross floor area, height or number of floors.
For example, Aldar’s published Alreeman II brochure shows a typical 510 m² plot with 382 m² of typical gross floor area. They are two different measurements, and the brochure explicitly presents the plan as illustrative. Neither number verifies what you can build on a particular plot being offered for sale.
Which document answers which question?
| Source | Question it helps answer | What it does not establish |
|---|---|---|
| Plot map and site plan | Am I looking at the correct parcel, boundaries and road frontage? | Whether your proposed villa, basement or annex will be approved. |
| Current plot-specific development controls and any applicable community design rules | What use, setbacks, floor area, footprint, levels and access constraints should I design around? | Whether your drawing complies or has been approved. |
| Consultant’s feasibility sketch | Does the intended house fit after applying the documented rules, access and practical requirements? | Final planning or building permission. |
| Issued building permit and approved drawings | What has the authority approved for this parcel and design? | Whether a changed design or a different parcel is covered. |
Start by finding the plot on Abu Dhabi’s MyLand map, then match it to the owner’s current site plan. The ADREC help guide for DARI explains the site-plan certificate service and notes that some requests need DMT review. Ask the seller to provide the plan if the parcel is not on your own account. If the plot number, boundary, frontage or dimensions differ across documents, resolve the mismatch before drawing a building envelope.
How a 510 m² plot can show 382 m² of floor area
Aldar identifies Alreeman II as a project in Al Shamkha. Its residential land brochure, Plan Type A, lets you see how the measurements relate. This is a reading exercise using Aldar’s typical diagram, not a survey, a sale offer or a current approval for any parcel.
| What you are measuring | Plan Type A example | What it means for the villa |
|---|---|---|
| Plot area | 17 m × 30 m = 510 m² | The land inside the plot boundary. The full rectangle is not space you can cover with the house. |
| Simple setback box | With 1.5 m on each side and 5 m front and 3 m rear, the rectangle inside those lines is 14 m × 22 m = 308 m². | A geometric screen based only on the brochure. It is not the permitted footprint. Coverage rules, access, easements or other constraints may narrow what is usable. |
| Gross floor area (GFA) | 382 m², shown as typical GFA in the brochure. | A building-area measure, separate from both the land area and the setback box. Do not treat it as ground-floor area or assume which spaces count. |
The 308 m² is our geometric calculation from the illustrated setbacks. The 382 m² is the developer’s stated typical GFA, not the result of that calculation. Ask the consultant to measure footprint and GFA separately and explain how each covered space and level is treated under the applicable controls.
Want to know the best real estate options in the UAE? Contact us today to inquire!
Contact us via WhatsAppWhat if the setbacks in two sources differ?
In September 2025, DMT announced changes to private villa rules, including a 1.5 m front setback from the street. The Alreeman II example shows 5 m at the front. The two sources are not equivalent. One describes amendments for private villas, the other illustrates a typical plot in a named development. Neither tells you, on its own, which control applies to the plot you are buying.
Give both references to the consultant if the difference affects your design. Ask for the current rule, its date, the relevant plot or phase, and whether separate community design approval or conditions apply. Until the answer is documented for your parcel, do not assume the smaller setback applies or that the older brochure still governs it.
What to have checked before making an offer
- Define the intended build. Give the consultant a simple brief covering the villa layout, parking, access, outdoor space and any basement, guest annex, rooftop room or separate family space you need. Ask which items are allowed, which require further approval and which do not fit.
- Ask for a sketch tied to the documents. Have the consultant write the site-plan reference and date, permitted use, applicable setbacks, height or levels, footprint and GFA limits or measurement rules, and what assumptions remain. Ask them to show road access and any known easement, utility corridor or connection issue that could change the layout or timetable.
- Separate a feasibility check from permit approval. DMT launched BINAA with an initial focus on new private villas. Ask your consultant to confirm the applicable submission route as well as any separate community sign-off. If the seller shows an existing approval, check the parcel, drawing revision and validity, and whether the authority will accept it for your intended design and ownership route.
- Decide what needs to be resolved before you commit. If your intended use, access or a must-have room depends on an unresolved rule, ask for that point in writing before making an unconditional offer. If the design fits on paper but utilities or the approval route are unclear, treat the build programme as unconfirmed.
For ownership, purchase costs and the decision between vacant land and a finished home, see the broader Abu Dhabi land-buying guide.
This guide is general information. It does not determine the development rights or permit status of any specific plot.